한국의

한국의

Get a Quote
제품

핫 제품

회사 뉴스

How to Install the Valve Gasket?
How to Install the Valve Gasket?
2023-06-07

Sealing gasket is a commonly used sealing spare part for machinery, equipment, etc. It is a material that plays a sealing role. Correct installation can ensure sealing performance and smooth operation of the equipment, otherwise it will damage the sealing gasket. Next, let's take a specific look at what to do. The correct installation of gaskets should be carried out when the flange connection structure or threaded connection structure, sealing surface, and gasket have been inspected without any doubt, and other valve components are intact and undamaged. 1. Before installing the gasket, apply a layer of graphite powder or lubricant mixed with engine oil (or water) to the sealing surface, gasket, thread, and rotating parts of the bolt and nut. The gasket and graphite should be kept clean. 2. The gasket should be installed on the sealing surface in a moderate and correct manner, without deviation, and should not extend into the valve chamber or rest on the shoulder. 3. Only one gasket is allowed to be installed, and it is not allowed to install two or more gaskets between the sealing surfaces to eliminate insufficient clearance between the two sealing surfaces. 4. The sealing of elliptical gaskets should ensure that the inner and outer rings of the gasket come into contact, and the two ends of the gasket should not come into contact with the bottom of the groove. 5. The installation of the O-ring should not only meet the design requirements for the ring and groove, but also have an appropriate amount of compression. On the premise of ensuring sealing, the smaller the compression deformation rate, the better, which can extend the service life of the O-ring. 6. Before installing the gasket, the valve should be in the open position to avoid affecting installation and damaging the valve components. When covering, it should be aligned with the position and should not be pushed or pulled into contact with the gasket to avoid displacement and scratches on the gasket. 7. The installation of gaskets for bolted or threaded connections should ensure that the gaskets are in a horizontal position (threaded gaskets with wrench positions should not be used with pipe wrenches). 8. Before tightening the gasket, it is necessary to have a clear understanding of the pressure, temperature, properties of the medium, and material characteristics of the gasket to determine the pre tightening force. The preload should be minimized as much as possible without leakage during pressure testing. 9. After tightening the gasket, it is necessary to ensure that there is a pre tightening gap between the connecting parts in case of gasket leakage. 10. When working at high temperatures, bolts will experience high-temperature creep, stress relaxation, and increased deformation, leading to leakage at the gasket and requiring hot tightening. On the contrary, under low temperature conditions, bolts will shrink and require cold loosening. 11. When liquid sealing gaskets are used for sealin...

게이트 밸브와 글로브 밸브의 차이점은 무엇입니까?
게이트 밸브와 글로브 밸브의 차이점은 무엇입니까?
2023-05-31

많은 사람들은 게이트 밸브와 글로브 밸브 모두 미디어를 차단하는 기능이 있으므로 사용할 때 다르지 않다고 생각합니다. 실제로 실제 적용에서 게이트 밸브와 글로브 밸브 사이에는 특정 차이점이 있습니다. 게이트 밸브 및 구조도 글로브 밸브 및 구조도 1. Having different structures. Gate valves are more complex in structure, higher in height, and larger in size than globe valves. Gate valves are shorter and higher in appearance than globe valves. Especially, opening the stem gate valve requires a higher height. If the installation position of the valve is limited, it is necessary to choose rising stem and non-rising stem gate valves and remind everyone to pay attention. 2. When fully open, it has different flow resistance. The flow resistance coefficient of ordinary gate valves is approximately 0.08~0.12. The pressure loss during the operation of the gate valve medium is small, and the fluid flow resistance is small. Gate valves are usually suitable for working conditions where frequent opening and closing are not required and the gate is kept fully open or closed. It is not suitable for adjustment and throttling. The resistance coefficient of a regular globe valve is about 3.5-4.5, and the opening and closing forces are very small. The flow resistance of the shut-off valve throughout its entire stroke is very high, and the required driving force or torque is also much greater. But it is very suitable for regulation and throttling. 3. The flow direction of the medium inside the valve body is different. Gate valves have the same effect when viewed from both sides. When installing a shut-off valve, the medium can enter from below and above the valve core. 4. The sealing surface of the gate valve has a certain degree of self-sealing ability. The valve core is in close contact with the sealing surface of the valve seat through medium pressure, achieving sealing performance and no leakage. The sealing surfaces of the shut-off valve only come into contact with each other when fully closed, and the relative sliding amount between the forcibly closed valve core and the sealing surface is very small, so the wear of the sealing surface is also very small. 5. The maintenance procedures are different. The maintenance of gate valves is not applicable to on-site pipelines, but the seat and disc of most globe valves can be replaced online without the need to remove the entire valve from the pipeline (when the valve is not under pressure). This is very suitable for situations where valves and pipelines are welded together. Gate and globe valves are both fully open and fully closed valves. When selecting valves in the application process, attention should be paid to the characteristics of the valves. Globe valves are usually used for small pipelines and better sealing performance. In steam systems and large diameter pipelines, gate valves with low fluid resistance are usually

Triple Eccentric Metal Hard Seal Butterfly Valve의 가공기술 및 구조적 특성 원문보기 KCI 원문보기 인용
Triple Eccentric Metal Hard Seal Butterfly Valve의 가공기술 및 구조적 특성 원문보기 KCI 원문보기 인용
2023-05-24

트리플 편심 메탈 하드 씰 버터 플라이 밸브는 고성능 밸브로서 내식성, 안정적인 밀봉 및 작은 개방 토크와 같은 장점이 있습니다. 밀봉 표면은 경사진 원추형 표면이며 밸브 본체 밀봉 링과 나비 플레이트 어셈블리 밀봉 링 사이의 접촉은 표면 접촉입니다. 작동 원리는 구동 장치의 토크로 나비 판 어셈블리를 직접 구동하여 나비 판 어셈블리의 밀봉 링이 밸브 본체 밀봉 링에 완전히 접촉하여 탄성 변형을 일으켜 밀봉하는 것입니다. 구조적 특성 1. The hard sealed butterfly valve adopts a three eccentric hard sealing structure, with almost no wear on the valve seat and butterfly plate, and has a sealing function that becomes tighter as the valve is closed. 2. The sealing ring is made of stainless steel, which has the dual advantages of metal hard sealing and elastic sealing. Both at low and high temperatures, it has excellent sealing performance, corrosion resistance, and long service life. 3. The sealing surface of the butterfly plate adopts surfacing cobalt based hard alloy, which is wear-resistant and has a long service life. 4. The large-sized butterfly plate adopts a quilted frame structure, with high strength, large flow area, and small flow resistance. 5. According to user requirements, hard sealed butterfly valves can be designed with bidirectional sealing function. During installation, it is not limited by the flow direction of the medium or affected by spatial location, and can be installed in any direction. 6. The drive device can be installed in multiple workstations (rotating 90 ° or 180 °), making it easy for users to use. Processing Technology Based on the structural characteristics of the triple eccentric metal hard seal butterfly valve, the sealing ring of the butterfly plate assembly is a combination of stainless steel plate, asbestos plate, or graphite. The valve body sealing ring is made of hard alloy with high hardness, and it is difficult to control the cutting amount, making it difficult to process and shape in one go. Moreover, the roughness requirements for the machined surface are very high. To ensure processing requirements, the process is as follows: Rough machining of valve body or butterfly plate assembly →→ Valve body sealing ring is welded with hard alloy for insulation and heat treatment to eliminate thermal stress →→ Sealing surface of rough turning of upper tooling →→ Upper tooling precision turning sealing surface →→ Grinding sealing surface with upper grinding head →→ Boring shaft holes for valve body and butterfly plate assembly →→ Strength test sealing test

다섯 개의 백성 중 하나
加载中...

mss SP-81 수동 러그 타입 나이프 게이트 밸브 양방향

The 나이프 게이트는 양방향 MSS-SP-81 에 따라 설계된 러그 형 밸브 및 산업 서비스 애플리케이션. The 차체와 시트의 디자인은 막힘 방지 산업에서 부유 물질을 차단하십시오.

  • 지불:

    30% when order confirmed, 70% before shipment
  • 제품 원산지:

    China
  • 색:

    Customization
  • 배송 포트:

    Shanghai, China
  • 리드 타임:

    30~60 days Ex Works after order confirmation
  • Material:

    2205
  • Method of Operation:

    Handwheel
지금 문의
제품 상세 정보

빠른 세부 사항

유형

KnifeGate 판막

크기

6 ''

설계 압력

150LB

구성

나이프 유형 게이트 밸브

연결 타입

러그 유형 , rf

작업 유형

핸드 휠

바디 재질

2205

시트 재료

EPDM

디자인 코드

mss SP-81

플랜지 치수

ASME B16.5

기온 범위 :

-29 ~. + 120 ℃

매질

물, 기름, 가스

유래

중국


풍모

모든 스테인리스 스틸 디자인

표준 나이프 게이트 밸브 : nps 2–24 (DN 50–600)

볼트로 고정 된 보닛 나이프 게이트 밸브 : nps 4 ~ 24 (DN 50–600)

ASME 클래스 : 1690-4500

0 ~ 14시 포장 기준

표준 나이프 게이트 밸브의 잠금 장치

환경 친화적 인 양방향 볼트로 고정 된 보닛 및 표준 바디 스타일

탄력 있고 금속 시트


기술 도면


제조 전

명판 & 포장


보고서

용 각 주문, Dervos you 를 보여줄 검사 보고서를 제공합니다. 전체 검사 프로세스 및 결과. 또한 you 우리가 제공하는 자료는 per 표준.



메시지를 남길

에 관심이 있다면 우리의 제품과한 자세한 내용을 알고 싶다면,메시지를 남겨주십시오 여기,우리가 응답할 것입니다 당신은 빨리 우리가 할 수 있습니다.

관련 상품
전기 작동 식 게이트 밸브
스테인레스 스틸 나이프 게이트 밸브 러그 전기 6 인치

mss-sp-81에 따라 설계된 6 인치 스텐레스 강 게이트 밸브는 클래스 150 및 전기 액츄에이터에 러그 유형 연결을 갖추고 있습니다. 빠른 세부 사항 유형 칼   게이트 밸브 크기 6 인치 설계 압력 아니   150 구성 칼   게이트 밸브 연결 타입 돌기   유형 작업 유형 전기 같은   액추에이터 바디 재료 ASTM   a351 cf8 트림 재료 ss304 디자인 코드 mss sp81 매질 물,   석유와 가스 유래 중국 관련 지식나이프 게이트 밸브는 무엇에 사용됩니까? 나이프 게이트 밸브는 원래 제지 산업을 위해 설계되었습니다. 나이프 게이트 밸브는 슬러리 액체와 같이 가장 부식성, 침식성 및 연마 성이 우수한 고체 미립자가있는 중질 액체에 특히 적용 할 수 있습니다. 쐐기 게이트 밸브에 비해 나이프 게이트 밸브는 엔드-투-엔드 치수가 짧고 무게가 가볍습니다. 또한 나이프 밸브에는 슬러리와 점성 매체를 절단하기 위해 디스크가 더 날카 로워졌습니다. 웨지 게이트 밸브와 나이프 게이트 밸브는 유량을 조절하지 않는 온-오프 기능에만 사용할 수 있습니다. dervos 고객 서비스dervos 고객 서비스를 통해 밸브를 구매하기 전, 도중 및 후에 걱정할 필요가 없습니다. 사전 판매우리는 제 시간에 응답하고 귀하의 요청에 따라 기술 지원을 제공합니다. 주문우리는 공장 및 고객과 생산 세부 사항을 확인합니다. 판매 확인서도 발송됩니다. 생산하는 동안 주문 상태를 알려주는 주간 보고서를 보내드립니다. 선적하기 전에 상황을 알려주기 위해 납품서가 발송됩니다. 18 개월 보증 dervos는 항상 제품에 대한 책임이 있습니다. 우리는 고객에게 걱정없이 18 개월 보증을 제공 할 것입니다.

단방향 나이프 게이트 밸브
플랜지 나이프 게이트 밸브 DN800 PN6 CF8M 기어 박스

스테인레스 스틸 나이프 게이트 밸브는 dn800 pn6 플랜지 엔드 및 기어 박스 작동으로 설계되었습니다. 연성 시트 나이프 게이트 밸브에는 단방향 밀봉이 있습니다. 빠른 세부 사항 유형 문   판막 크기 dn800 설계 압력 pn6 구성 단방향,   부드러운 자리 연결 타입 플랜지   종료 작업 유형 변속 장치   움직이는 바디 재료 cf8m 디스크 재료 ss316l 줄기 재료 ss316 시트 재료 ptfe 디자인 코드 mss sp81 매질 물,   석유와 가스 유래 중국 치수 확인 압력 테스트

나이프 게이트 밸브
DN150 PN10 단방향 나이프 게이트 밸브 웨이퍼 RF 주철

DN150 PN10 단방향 나이프 게이트 밸브 단일 피스의 스테인리스 스틸 본체 디자인이 특징이며 범용에서 가혹한 매체에 이르는 응용 분야에서 테스트된 성능을 제공합니다.

게이트 밸브
나이프 게이트 밸브 CF8 4인치 150LB 러그 타입 핸드휠

러그 유형 나이프 게이트 밸브는 스테인리스 스틸 CF8,로 만든 mss-sp-81.에 따라 설계되었습니다. 4인치 게이트 밸브에는 150LB 플랜지 연결 및 핸드휠 작동이 있습니다.

다섯 개의 백성 중 하나
3 '' 150LB API 6D 확장 플러그 밸브 DBB 무 윤활 rf

The 3 인치 150LB 확장 플러그 밸브는 확실한 차단, 검증 가능한 제로 누출, 이중 블록 및 블리드 기능이 필요합니다.

용접 볼 밸브 단조 스틸 금속 장착
10 인치 완전 용접 볼 밸브 금속 시트 베어 스템

20 인치 금속 시트형 볼 밸브는 고체 입자를 사용하여 고온 적용 또는 적용을 위해 설계되었습니다. 밸브에는 트러 니언 장착 유형에 속하는 용접 몸체, rf 플랜지 연결, 액추에이터 용 베어 스템이 있습니다. 빠른 세부 사항 유형 볼 밸브 크기 20 " 압력 아니 600 구성 트러 니언 타입,   일체형 본체, 완전 용접, 금속-금속 시트 연결 플랜지 조작 벌거 벗은 줄기 신체   재료 서서히 나아가는   강철 ASTM a105 디자인   표준 API 6D 압력   & amp; 온도 asme b16.34 면 대면   치수 asme b16.10 종료   연결 asme b16.5 검사 API 598 온도   범위 -29 ℃ ~ + 200 ℃ 미디어 기름,   수성 가스 치수 클래스 600 dn mm 50 65 80 100 150 200 250 300 350 400 450 500 nps 에 2 2.5 삼 4 6 8 10 12 14 16 18 20 엘(rf) mm 292 330 356 432 559 660 787 838 889 991 1092 1194 에 11.5 13 14 17 22 26 31 33 35 39 43 47 l1(bw) mm 292 330 358 432 22 660 787 838 889 991 1092 1194 에 11.5 13 14 17 559 26 31 33 35 39 43 47 l2(rtj) mm 295 333 359 435 562 664 791 841 892 994 1095 1200 에 11.63 13.13 14.13 17.13 22.13 26.13 31.13 33.13 35 39.5 43.1 47.3 h mm 153 165 195 213 272 342 495 580 630 725 800 850 에 6.02 6.5 7.68 8.39 10.7 13.5 19.5 22.85 24.8 28.5 31.5 33.5 할 (w) mm 600 850 1250 1300 1500 년 * 350 * 350 * 600 * 600 * 800 * 800 * 800 에 23.62 33.46 49.25 51.22 59 13.8 13.8 23.6 23.6 31.5 31.5 31.5 rf (kg) & emsp; 38 56 66 122 217 350 660 820 830 1160 1420 1650 bw (kg) & emsp; 31 51 58 117 200 327 605 790 800 1030 1305 1505 * 웜 기어 또는 전동 액추에이터 작동 관련 지식금속 장착 볼 밸브를 언제 사용해야합니까? 금속 시트 볼 밸브의 시트는 종종 ptfe, peek, nylon, teflon 및 devlon과 같은 부드러운 시트 재료 대신 스텔 라이트, 스테인레스 스틸 또는 텅스텐 카바이드입니다. 이 금속 대 금속 시트 볼 밸브는 특히 다음에 적용됩니다.고온 매체고마 모를위한 고형 미립자 함유 미디어높은 침식 및 부식과 같은 심각한 상태의 매체중유처럼 점도가 높은 매체 우리의 주요 제품 범위dervos 주요 제품에는 고객의 요청에 따라 볼 밸브, 버터 플라이 밸브, 체크 밸브, 게이트 밸브, 글로브 밸브 및 플러그 밸브가 포함됩니다.

딘 글로브 밸브 앵글 타입
앵글 타입 글로브 밸브 DN65 PN16 GS-C25 상승 스템

dn65 pn16 앵글 타입 글로브 밸브는 주강 1.0619 몸체와 ss304 트림 재질로 구성되어 있으며 상승 스템, 핸드 휠, rf 플랜지가 있습니다. 빠른 세부 사항 유형 지구   판막 표준 크기 dn   65 정상 압력 pn   16 구성 각도   패턴, bb 연결 타입 플랜지 조작 핸드 휠 디자인 코드 소음   3356 면 대면 en   558 연결 en1092 테스트 & amp;   검사 en12266 바디 재료 GS-C25   (1.0619) 해당하는 -29 ℃ ~ + 425 ℃ 신청 울다 관련 지식 왜 앵글 타입 글로브 밸브를 사용합니까? 앵글 글로브 밸브는 엘보우 또는 여분의 파이프 용접을 사용하지 않고 흐름 방향을 90도 회전시켜 파이프 라인의 조인트 수를 줄이고 설치 시간을 절약하며 압력 강하 & amp; 흐름 저항. 앵글 패턴 글로브 밸브는 슬러 깅 효과를 처리 할 수 ​​있기 때문에 맥동 흐름주기에 사용됩니다. 우리의 주요 제품 범위 산업 밸브의 숙련 된 공급 업체 및 공급 업체로서 dervos는 주강 밸브, 단조 밸브, 주철 밸브, 스테인레스 스틸 밸브, 청동 밸브, 황동 밸브 및 합금강 밸브 등을 공급하여 해수, 물, 기름, 그리고 가스 신청.

고성능 버터 플라이 밸브
고성능 버터 플라이 밸브 러그 타입 기어 작동 wcb

고성능 버터 플라이 밸브는 이중 편심 또는 이중 오프셋 구조로 설계되었습니다. 밸브에는 rptfe 소프트 시트와 함께 캐스트 스틸 wcb 바디, 스테인레스 스틸 디스크 및 스템이 있습니다. 빠른 세부 사항 유형 나비   판막 공칭 크기 6 인치 명사 같은   압력 클래스 150 구조 이중 오프셋   이중 편심, 소프트 시트 연결   유형 러그 타입 조작 기어 작동 디자인 코드 API 609 면 대면 asme b16.10 연결 종료 asme 16.5 테스트 & amp;   검사 API 598 바디 재료 캐스트 스틸 wcb 트림 재료 cf8m 디스크,   17-4PH 스템, RPTFE 시트 신청 물, 기름,   가스 dervos 검사 보고서

게이트 밸브
단조 강철 게이트 밸브 1 인치 300LB 솔리드 웨지

1인치 단조 강철 게이트 밸브는 일체형 플랜지, 볼트식 보닛, 상승 스템 및 솔리드 쐐기 및 볼트식 보닛.으로 구성됩니다. 밸브에는 설계 표준 API 602 및 검사 표준 API 598.이 있습니다. dervos는 고객에게 다양한 크기, 재질, 표준, 설계 압력, 구조, 작동 유형 및 연결 유형.의 밸브를 제공함으로써 맞춤형 서비스를 제공할 수 있습니다.

거르는 사람
DN32 PN16 주강 Y형 스트레이너 BC RF WCB

DN32 PN16 Y형 스트레이너는 EN12516-1 표준에 따라 제작됩니다. 밸브 본체는 WCB로 제작되었습니다. 압력 Y형의 구조적 특성을 가지고 있습니다. 연결 모드는 RF입니다.

두 조각 캐스트 스틸 볼 밸브
캐스팅 2 피스 볼 밸브 4 인치 클래스 150 렌치

2 피스 타입 플로팅 볼 밸브 전체 포트, 화재 안전 설계, 안티 분출 스템, ANSI 150 플랜지 및 레버 작동. 탄소강 볼 밸브는 a216 wcb 바디, f316 스템 및 볼, ptfe 소프트 시트로 설계되었습니다. 빠른 세부 사항 유형 볼 밸브 크기 4 " 압력 150 파운드 구성 플로팅 타입   볼, 2 피스 바디, 풀 보어 연결 높인   면 플랜지 끝 조작 렌치   조작 신체   재료 캐스트 스틸   wcb 손질   재료 ss316 및 ptfe 디자인 표준 API 6D 압력   & amp; 임시 코드 asme b16.34 면 대면 asme b16.10 종료   연결 asme b16.5 검사   암호 API 6D 온도   범위 -29 ℃ ~ + 125 ℃ 미디어 물, 기름   가스 소재 & amp; 치수 아니 부품 이름 탄소   강철에서 ASTM으로 스테인리스   강철에서 ASTM으로 wcb lcb cf8 cf8m cf3 cf3m 1 신체 a216 화장실 a352 lcb a351 cf8 a351 cf8m a351 cf3 a351 cf3m 2 보닛 너트 a194 2 시간 a194 4 a194 8 삼 보닛 볼트 a193 b7 a320 l7 a193 b8 4 캡 a216 화장실 a352 lcb a351 cf8 a351 cf8m a351 cf3 a351 cf3m 5 틈 메우는 물건 ss 나선형 상처 / 흑연 또는   ss 나선형 상처 / ptfe 6 공 a105 / ep.cr 또는 f6 a182 f6 a351 cf8 a351 cf8m a351 cf3 a351 cf3m 7 좌석 링 rptfe 또는 pom 8 작은 봄 스테인레스 9 작은 공 a182 f304 a182 f316l 10 줄기 a182 f6 a182 f6 a182 f304 a182 f316 a182 f304l a182 f316l 11 줄기 좌석 ptfe 12 줄기 포장 ptfe 또는 흑연 13 선 a182 f6 a182 f304 a182 f316 a182 f304l a182 f316l 14 글 랜드 볼트 a193 b7 a193 b8 15 갈드 플랜지 a216 화장실 a351 cf8 16 포지셔닝 플레이트 강철 17 브렌치 a216 화장실 재료는   ASTM 표준에 따라 클래스 150 dn mm 15 20 25 40 50 65 80 100 150 200 250 nps 에 0.5 0.75 1 1.5 2 2.5 삼 4 6 8 10 엘 (rf) mm 108 117 127 165 178 191 203 229 394 457 533 에 4.25 4.6 5 6.5 7 7.5 8 9 15.5 18 21 l1 (bw) mm 140 152 165 190 216 241 283 305 457 521 559 에 5.5 6 6.5 7.48 8.5 9.5 11.13 12 18 20.5 22 l2 (rtj) mm 119 129.7 139.7 178 191 203 216 241 406 470 546 에 4.69 5.11 5.5 6.9 7.5 8 8.5 9.5 16 18.5 21.5 h mm 66 74 87 105 132 152 182 215 250 285 495 에 2.6 2.9 3.48 4.2 5.28 6.08 7.28 8.6 10 11.4 19.5 할 (w) mm 130 130 160 230 400 400 600 850 1100 1500 년 * 350 에 5.1 5.11 6.3 9 15.74 15.74 23.62 33.46 43.3 59 13.8 rf (kg) & emsp; 2.3 삼 4.5 7 15 20 25 40 97 160 240 bw (kg) & emsp; 2.0 2.5 3.8 5.8 12 17 21 36 92.8 154 227 * 웜 기어 또는 전동 액추에이터 작동 특별 시험 & amp; 검사 dervos는 정기적 인 유압 테스트 및 공기 테스트 외에도 pt 테스트, rt 테스트, ut 테스트, 극저온 테스트, 저 누출 테스트, 내화 테스트 및 경도 테스트 등과 같은 고객의 요청에 따라 특수 테스트를 수행 할 수 있습니다 .

메시지를 남겨주세요

    에 관심이 있다면 우리의 제품과한 자세한 내용을 알고 싶다면,메시지를 남겨주십시오 여기,우리가 응답할 것입니다 당신은 빨리 우리가 할 수 있습니다.

제품

접촉