한국의

한국의

Get a Quote
제품

핫 제품

회사 뉴스

How to Install the Valve Gasket?
How to Install the Valve Gasket?
2023-06-07

Sealing gasket is a commonly used sealing spare part for machinery, equipment, etc. It is a material that plays a sealing role. Correct installation can ensure sealing performance and smooth operation of the equipment, otherwise it will damage the sealing gasket. Next, let's take a specific look at what to do. The correct installation of gaskets should be carried out when the flange connection structure or threaded connection structure, sealing surface, and gasket have been inspected without any doubt, and other valve components are intact and undamaged. 1. Before installing the gasket, apply a layer of graphite powder or lubricant mixed with engine oil (or water) to the sealing surface, gasket, thread, and rotating parts of the bolt and nut. The gasket and graphite should be kept clean. 2. The gasket should be installed on the sealing surface in a moderate and correct manner, without deviation, and should not extend into the valve chamber or rest on the shoulder. 3. Only one gasket is allowed to be installed, and it is not allowed to install two or more gaskets between the sealing surfaces to eliminate insufficient clearance between the two sealing surfaces. 4. The sealing of elliptical gaskets should ensure that the inner and outer rings of the gasket come into contact, and the two ends of the gasket should not come into contact with the bottom of the groove. 5. The installation of the O-ring should not only meet the design requirements for the ring and groove, but also have an appropriate amount of compression. On the premise of ensuring sealing, the smaller the compression deformation rate, the better, which can extend the service life of the O-ring. 6. Before installing the gasket, the valve should be in the open position to avoid affecting installation and damaging the valve components. When covering, it should be aligned with the position and should not be pushed or pulled into contact with the gasket to avoid displacement and scratches on the gasket. 7. The installation of gaskets for bolted or threaded connections should ensure that the gaskets are in a horizontal position (threaded gaskets with wrench positions should not be used with pipe wrenches). 8. Before tightening the gasket, it is necessary to have a clear understanding of the pressure, temperature, properties of the medium, and material characteristics of the gasket to determine the pre tightening force. The preload should be minimized as much as possible without leakage during pressure testing. 9. After tightening the gasket, it is necessary to ensure that there is a pre tightening gap between the connecting parts in case of gasket leakage. 10. When working at high temperatures, bolts will experience high-temperature creep, stress relaxation, and increased deformation, leading to leakage at the gasket and requiring hot tightening. On the contrary, under low temperature conditions, bolts will shrink and require cold loosening. 11. When liquid sealing gaskets are used for sealin...

게이트 밸브와 글로브 밸브의 차이점은 무엇입니까?
게이트 밸브와 글로브 밸브의 차이점은 무엇입니까?
2023-05-31

많은 사람들은 게이트 밸브와 글로브 밸브 모두 미디어를 차단하는 기능이 있으므로 사용할 때 다르지 않다고 생각합니다. 실제로 실제 적용에서 게이트 밸브와 글로브 밸브 사이에는 특정 차이점이 있습니다. 게이트 밸브 및 구조도 글로브 밸브 및 구조도 1. Having different structures. Gate valves are more complex in structure, higher in height, and larger in size than globe valves. Gate valves are shorter and higher in appearance than globe valves. Especially, opening the stem gate valve requires a higher height. If the installation position of the valve is limited, it is necessary to choose rising stem and non-rising stem gate valves and remind everyone to pay attention. 2. When fully open, it has different flow resistance. The flow resistance coefficient of ordinary gate valves is approximately 0.08~0.12. The pressure loss during the operation of the gate valve medium is small, and the fluid flow resistance is small. Gate valves are usually suitable for working conditions where frequent opening and closing are not required and the gate is kept fully open or closed. It is not suitable for adjustment and throttling. The resistance coefficient of a regular globe valve is about 3.5-4.5, and the opening and closing forces are very small. The flow resistance of the shut-off valve throughout its entire stroke is very high, and the required driving force or torque is also much greater. But it is very suitable for regulation and throttling. 3. The flow direction of the medium inside the valve body is different. Gate valves have the same effect when viewed from both sides. When installing a shut-off valve, the medium can enter from below and above the valve core. 4. The sealing surface of the gate valve has a certain degree of self-sealing ability. The valve core is in close contact with the sealing surface of the valve seat through medium pressure, achieving sealing performance and no leakage. The sealing surfaces of the shut-off valve only come into contact with each other when fully closed, and the relative sliding amount between the forcibly closed valve core and the sealing surface is very small, so the wear of the sealing surface is also very small. 5. The maintenance procedures are different. The maintenance of gate valves is not applicable to on-site pipelines, but the seat and disc of most globe valves can be replaced online without the need to remove the entire valve from the pipeline (when the valve is not under pressure). This is very suitable for situations where valves and pipelines are welded together. Gate and globe valves are both fully open and fully closed valves. When selecting valves in the application process, attention should be paid to the characteristics of the valves. Globe valves are usually used for small pipelines and better sealing performance. In steam systems and large diameter pipelines, gate valves with low fluid resistance are usually

Triple Eccentric Metal Hard Seal Butterfly Valve의 가공기술 및 구조적 특성 원문보기 KCI 원문보기 인용
Triple Eccentric Metal Hard Seal Butterfly Valve의 가공기술 및 구조적 특성 원문보기 KCI 원문보기 인용
2023-05-24

트리플 편심 메탈 하드 씰 버터 플라이 밸브는 고성능 밸브로서 내식성, 안정적인 밀봉 및 작은 개방 토크와 같은 장점이 있습니다. 밀봉 표면은 경사진 원추형 표면이며 밸브 본체 밀봉 링과 나비 플레이트 어셈블리 밀봉 링 사이의 접촉은 표면 접촉입니다. 작동 원리는 구동 장치의 토크로 나비 판 어셈블리를 직접 구동하여 나비 판 어셈블리의 밀봉 링이 밸브 본체 밀봉 링에 완전히 접촉하여 탄성 변형을 일으켜 밀봉하는 것입니다. 구조적 특성 1. The hard sealed butterfly valve adopts a three eccentric hard sealing structure, with almost no wear on the valve seat and butterfly plate, and has a sealing function that becomes tighter as the valve is closed. 2. The sealing ring is made of stainless steel, which has the dual advantages of metal hard sealing and elastic sealing. Both at low and high temperatures, it has excellent sealing performance, corrosion resistance, and long service life. 3. The sealing surface of the butterfly plate adopts surfacing cobalt based hard alloy, which is wear-resistant and has a long service life. 4. The large-sized butterfly plate adopts a quilted frame structure, with high strength, large flow area, and small flow resistance. 5. According to user requirements, hard sealed butterfly valves can be designed with bidirectional sealing function. During installation, it is not limited by the flow direction of the medium or affected by spatial location, and can be installed in any direction. 6. The drive device can be installed in multiple workstations (rotating 90 ° or 180 °), making it easy for users to use. Processing Technology Based on the structural characteristics of the triple eccentric metal hard seal butterfly valve, the sealing ring of the butterfly plate assembly is a combination of stainless steel plate, asbestos plate, or graphite. The valve body sealing ring is made of hard alloy with high hardness, and it is difficult to control the cutting amount, making it difficult to process and shape in one go. Moreover, the roughness requirements for the machined surface are very high. To ensure processing requirements, the process is as follows: Rough machining of valve body or butterfly plate assembly →→ Valve body sealing ring is welded with hard alloy for insulation and heat treatment to eliminate thermal stress →→ Sealing surface of rough turning of upper tooling →→ Upper tooling precision turning sealing surface →→ Grinding sealing surface with upper grinding head →→ Boring shaft holes for valve body and butterfly plate assembly →→ Strength test sealing test

글로브 밸브 EN10213
加载中...

PN25 DN80 스트레이트 타입 글로브 밸브 EN10213

EN 13709 설계 및 제조. EN558-1 대면 치수. EN1092-B1 플랜지 및 치수. EN12266 시험 및 검사 기준.

  • 지불:

    30% when order confirmed, 70% before shipment
  • 제품 원산지:

    China
  • 색:

    Customization
  • 배송 포트:

    Shanghai, China
  • 리드 타임:

    30~60 days Ex Works after order confirmation
  • Material:

    Cast Steel
  • Method of Operation:

    Handwheel
지금 문의
제품 상세 정보

DN80 PN25 글로브 밸브; 스트레이트 타입; 볼트 보닛; 외부 멍에; 핸드휠 작동 EN 10213;


제품 설명

유형

글로브 밸브

크기

DN80

압력

PN25

건설

똑바로

연결

RF

본체 재질

EN 10213 1.0619

시트 재질

오버레이 STL6

디자인 코드

EN13709

면 대면

EN558-1

연결 종료

EN1092-B1

테스트 & 검사

EN12266

적용 매체

물, 기름, 가스

기원

중국


구조 기능

1. 이중벽 벨로우즈 씰의 표준 설계

2. 방열 보닛 디자인;

3. 윤활유 저장 장치로;

4, 줄기 견과를 고치기 위하여 circlip의 디자인으로;

5. 적당한 제품 구조, 믿을 수 있는 밀봉 성과 및 좋은 외관;

6. 씰링 표면은 내마모성, 내식성, 마찰 방지 성능 및 긴 수명을 갖는 Co 기반 경질 합금으로 용접됩니다.

7. 줄기에는 내식성 및 마찰 방지 성능이 우수한 질화 처리가되어 있습니다.

8. 줄기 움직임을 위한 위치 표시기로;


명판


포장

우리의 주요 제품 범위

경험이 풍부한 산업용 밸브 공급업체이자 공급업체인 Dervos는 해수, 물, 오일, 및 가스 적용.



메시지를 남길

에 관심이 있다면 우리의 제품과한 자세한 내용을 알고 싶다면,메시지를 남겨주십시오 여기,우리가 응답할 것입니다 당신은 빨리 우리가 할 수 있습니다.

관련 상품
플랜지 글로브 밸브 OS & Y
스테인레스 스틸 글로브 밸브 pn16 dn50 플랜지 핸드 휠

pn16 dn50 스테인리스 플랜지 글로브 밸브는 직선 패턴 구조, 볼트 형 보닛 및 핸드 휠 작동 방식을 갖추고 있습니다. OS 글로브 밸브는 din 3356에 따라 설계되었습니다. 빠른 세부 사항 유형 지구   판막 표준 크기 dn50 정상 압력 pn16 구성 bb,   상승 스템, 플러그 디스크, 일체형 시트 연결 타입 플랜지 작업 유형 변속 장치 디자인 코드 소음   3356 면 대면 식사 3202 플랜지 끝 소음   2543 테스트 & amp;   검사 소음   3230 바디 재료 스테인리스   강철 트림 재료 스테인리스   강철 온도 범위 -196 ℃ ~ + 800 ℃ 매질 물, 기름 및 가스 유래 중국 디자인 기능 1. 스트레이트 패턴 바디 구조 2.OS & Y; 상승 줄기 3. 볼트 보닛 비스듬한 장치 가동에 4.available 5. 플러그 타입 디스크 벨브 가동 도중 밀봉 얼굴에 6.little 마포 7. 소형 설치 공간 필요 dervos 주요 제품군 전체 제품 범위를 갖춘 dervos 제품 목록에는 게이트, 글로브, 체크, 볼, 버터 플라이, 체크, 플러그 밸브 및 스트레이너가 포함됩니다. 우리는 또한 바다 벨브, 감압 밸브, 통제 지구 벨브, 송유관 벨브 등을 제공해서 좋습니다

직선형 글로브 밸브 플랜지
캐스트 스틸 글로브 밸브 12 인치 ANSI 150 WCB 기어 박스

12 인치 150 파운드 캐스트 스틸 글로브 밸브는 카본 스틸 WCB 몸체와 트림 8, 기어 박스, RF 플랜지, BB 및 플러그 디스크로 구성됩니다. 빠른 세부 사항 유형 지구   판막 크기 12 인치 압력 수업   150 구성 볼트   보닛, 직선형, 플러그 디스크, os & amp; y 연결 플랜지   연결 조작 기어 디자인 코드 bs   1873 면 대면 저 같은   b16.10 플랜지 연결 저 같은   b16.5 압력 및   온도 저 같은   b16.34 테스트 & amp;   검사 API   598 바디 재료 a216   wcb 트림 재료 손질   8 온도 범위 -29 ℃ ~ + 427 ℃ 신청 울다 유래 중국 치수 클래스 150 nps 에 2 2 1/2 삼 4 5 6 8 10 12 dn mm 50 65 80 100 125 150 200 250 300 l-l1(rf-bw) 에 8 8-1 / 2 9-1 / 2 11-1 / 2 14 16 19-1 / 2 24-1 / 2 27-1 / 2 mm 203 216 241 292 256 406 495 622 698 l2(rtj) 에 8-1 / 2 9 10 12 14-1 / 2 16-1 / 2 20 25 28 mm 216 229 254 305 368 419 508 635 711 l3 mm 102 108 121 146 178 203 248 311 349 h(열다) 에 14-11 / 16 15-3 / 8 16-9 / 16 20-1 / 4 21-3 / 16 22-5 / 15 24-5 / 8 28 39 mm 373 390 421 515 538 567 626 712 990 승 에 7-7 / 8 9-7 / 8 9-7 / 8 11-13 / 16 11-13 / 16 13-3 / 4 15-3 / 4 17-3 / 4 24 mm 200 250 250 300 300 350 400 450 610 wt(킬로그램) rf 22 29 42 64 77 105 154 288 507 bw 19 25 34 49 65 82 131 249 430 관련 지식게이트 밸브와 글로브 밸브의 차이점은 무엇입니까? 게이트 밸브와 글로브 밸브는 우리가 알고있는 가장 일반적인 밸브 중 하나입니다. 그들 사이의 차이점은 다음과 같습니다. 1. 게이트 밸브는 온-오프 기능에만 사용됩니다. 그러나 글로브 밸브는 동시에 차단 및 조절에 사용될 수 있습니다.2. 글로벌 밸브의 유동 저항은 게이트 밸브보다 큽니다. 마찬가지로 글로브 밸브는 게이트 밸브보다 압력 강하가 더 큽니다.3. 게이트 밸브는 개방 높이의 관점에서 글로브 밸브보다 더 큰 설치 공간이 필요합니다.4. 게이트 밸브 씰링면은 글로브 밸브보다 마모가 더 심합니다.5. 글로벌 밸브의 토크 값이 게이트 밸브보다 큽니다. 품질 검사품질은 dervos의 모든 것을 의미합니다. 품질 점검 팀은 표준 절차에 따라 검사를 수행하고 보고서를 제공합니다. 우리의 QC 팀은 주조 및 단조, 가공, 압력 테스트, 치수 검사, 도장 및 밸브 품질을 검사합니다. 포장.

다섯 개의 백성 중 하나
WCB 글로브 밸브 1500lb 2 인치 핸드 휠

astm216 wcb로 제작 된 2 인치 1500lb 글로브 밸브는 BS 1873에 따라 설계되었습니다. 핸드 휠로 작동하며 rtj에 의해 파이프 라인에 연결됩니다. 글로브 밸브의 몸체와 디스크에는 13cr이 포함되어 있으므로이 밸브는 부식에 대한 저항력이 뛰어납니다. 빠른 세부 사항 유형 글로브 밸브 공칭 직경 2 인치 공칭 압력 1500 파운드 구성 볼트 보닛 연결 rtj 조작 핸드 휠 디자인 및 제조 bs 1873 끝으로 종료 asme b16.10 플랜지 끝 치수 asme b16.5 테스트 & amp; 검사 API 598 온도 범위 -29 ℃ ~ + 425 ℃ 바디 재료 ASTM A216 WCB + 13CR 디스크 재료 ASTM A105 WCB + 13CR 미디어 w.o.g. dervos 품질 검사 시스템 dervos에서는 전체 제조 공정에서 품질을 관리합니다. 주조 검사 : 우리는 당신이 속이지 않을 것을 보장하는 거친 주조, 자격이없는 벽 두께, 화학 성분 등과 같은 원료의 문제를 찾을 수 있습니다. 가공 검사 : 한편으로이 프로세스를 통해 가공 정확도를 보장 할 수 있습니다. 다른 한편으로, 수리 및 재생에 더 많은 시간을 확보하기 위해 가능한 빨리 가공 실수를 발견 할 수있었습니다. 최종 검사 : 최종 검사 활동에는 문서 및 QC 기록 검토, 육안 검사, 치수 검사, 압력 테스트, 도장 및 포장 검사가 포함됩니다. 직접 방문하여 검사 할 필요가 없으며 모든 문서가 증거로 제공 될 수 있습니다.

핸 운영하는 글로브 밸브
8 인치 300 파운드 캐스트 강철 A350 글로브 밸브 BS1873BW

캐스트 철강 글로브 밸브 설계되었으로 당 BS1873. 신체 보닛,외부 나사 및 요크,핸들,8 인치 밸브,밸브에 적합한 일반적인 작동 상태입니다.

다섯 개의 백성 중 하나
300 파운드 SS 비유적인 글로브 밸브 핸 RF

1-1/2inch 글로브 밸브,에 따라 설계되었 API623,폭탄을 가지고 있 모 몸 포물선 플러그의 최적화의 원활한 흐름다. 이 밸브는 스테인리스로 만들고 있는 수동 핸들과 운영 및 유지합니다.

다섯 개의 백성 중 하나
캐스트 스틸 글로브 밸브 스트레이트 SDNR Fnpt

글로브 밸브가없는 디자인, 역류 방지 언제 개방 위치에서 격리 듀티에도 적합합니다. 수동으로 운영되고, 핸드 휠이 제공됩니다.

글로브 밸브
nps 6 600lb 글로브 밸브 주강 rf api623

astm216 WCB로 만든 6인치 600lb 글로브 밸브는 api623에 따라 설계되었습니다

글로브 밸브
WCB 2 인치 300LB 글로브 밸브 BB 라이징 스템 핸드 휠

빠른 세부 정보 유형 글로브 밸브 공칭 크기 국민연금 2 공칭 압력 클래스 300 건설 BB, 라이징 스템, 일체형 시트 연결 타입 플랜지 작업 유형 핸드휠 디자인 코드 BS1873 면 대면 ASME B16.10 플랜지 끝 ASME B16.5 테스트 & 검사 API 598 본체 재질 WCB+STL 트림 소재 F316+STL 온도 범위 -29℃~425℃ 중간 물, 석유 및 가스 기원 중국 디자인 기능 1. 직선형 몸체 구조 2. OS&Y, 라이징 스템 3. 볼트 보닛 4. 베벨 기어 작동 가능 5. 플러그형 디스크 6. 밸브 작동시 실링면의 마모가 적음 7. 더 작은 설치 공간 필요 기술 도면 치수 확인 증인 시험 포장 우리의 서비스 Dervos 고객 서비스는 우리의 가장 큰 경쟁력 중 하나입니다. Dervos에서는 다음을 제공합니다. 1. 24시간 이내 또는 3일 이내 견적 이를 통해 견적 제출 마감일을 준수하고 작업 효율성을 높일 수 있습니다. 2. 주간 주문 상태 보고서 이런 식으로 주문에 대한 명확한 그림을 얻을 수 있습니다. 상태 업데이트를 요청하는 데 시간을 낭비할 필요가 없습니다. 3.18개월 보증 기간 보증서는 배송 후 발행되며 밸브 구입 후 걱정하실 필요는 없습니다. 4. 3일이내의 민원처리 불만 사항에 대한 신속하고 책임 있는 조치는 귀하의 평판을 보호하고 재정적 손실을 최대한 줄일 것입니다. 인증서 Dervos는 ISO 9001, PED CE, EAC, API 607, API 6D, API 6A 등과 같은 클라이언트의 요청에 대한 보고서를 제공할 수 있습니다.

글로브 밸브
6" 300LB 주강 글로브 밸브 BB BW WCB API598

6" 300LB 글로브 밸브는 BS1873 표준에 따라 만들어집니다. 밸브 본체는 WCB로 만들어집니다. 스트레이트 스루, 볼트 커버, 파라볼릭 디스크, 표준 흐름, 바디 밸브 시트의 구조적 특성을 가지고 있습니다. 연결 모드는 BW입니다. 그리고 그것은 핸드 휠 작동 모드가 있습니다.

글로브 밸브
3" 600LB 주강 글로브 밸브 BB RTJ CF8 핸드 휠 BS1873

3" 600LB 글로브 밸브는 BS1873 표준에 따라 만들어집니다. 밸브 본체는 ASTM A351 CF8+STL로 만들어집니다. 볼트 커버와 직선형의 구조적 특성을 가지고 있습니다. 연결 모드는 RTJ입니다. 그리고 핸드 휠 작동 모드가 있습니다. .

웨이퍼 체크 밸브
API594 3" 150LB 듀얼 플레이트 웨이퍼 체크 밸브 API598 LCC

3" 150LB 웨이퍼 체크 밸브는 API594 규격에 따라 만들어집니다. 밸브 본체는 A352 LCC + 316으로 만들어집니다. 더블 플레이트와 빌트인 타입의 구조적 특징을 가지고 있습니다. 연결 모드는 웨이퍼 타입입니다.

압력 씰 보닛 게이트 밸브
씰 보닛 게이트 밸브 bw 8 인치 2500lb

8 인치 클래스 2500 게이트 밸브는 압력 실 보닛, 맞대기 용접 연결 및 기어 박스 작동으로 설계되었습니다. 8 인치 게이트 밸브에는 탄소강 wcb 본체와 트림 5가 있습니다. 빠른 세부 사항 유형 문   판막 크기 8 인치 설계 압력 아니   2500 구성 압력   실링 보닛, 플렉시블 웨지, 금속-금속 시트 연결 타입 대상   용접 (sw) 작업 유형 변속 장치   조작 바디 재료 a217   화장실 트림 재료 트림 5 디자인 코드 API 600 대면 치수 저 같은   b16.10 연결 종료 저 같은   b16.25 압력 및 온도 저 같은   b16.34 매질 물,   석유와 가스 유래 중국 치수 & amp; 재료 nps dn 수업 2 2 1/2 삼 4 6 8 10 12 14 16 18 20 24 50 65 80 100 150 200 250 300 350 400 450 500 600 l (rf) 900 파운드 368 419 381 457 610 737 838 965 1029 1130 & emsp; & emsp; & emsp; 1500 파운드 368 419 470 546 705 832 991 1130 1257 1384 & emsp; & emsp; & emsp; 2500 파운드 451 508 578 673 917 1022 1270 & emsp; & emsp; & emsp; & emsp; & emsp; & emsp; l1 (bw) 900 파운드 216 254 305 355 508 660 787 914 991 1092 1346 1473 1600 년 1500 파운드 216 254 305 406 559 711 864 991 1067 1194 1697 & emsp; & emsp; 2500 파운드 279 330 368 457 610 762 914 1041 1118 1245 & emsp; & emsp; & emsp; l2 (rtj) 900 파운드 371 422 384 460 613 740 841 968 1038 1140 & emsp; & emsp; & emsp; 1500 파운드 371 422 473 549 711 841 1000 1146 1276 1407 & emsp; & emsp; & emsp; 2500 파운드 454 514 584 683 927 1038 1292 & emsp; & emsp; & emsp; & emsp; & emsp; & emsp; h (오픈) 900 파운드 554 637 680 796 1084 1372 1494 1550 1960 2210 & emsp; & emsp; & emsp; 1500 파운드 554 637 767 875 1094 1372 1655 1834 2150 2260 2460 2721 2940 2500 파운드 610 654 753 850 1254 1374 1685 1894 2226 2382 2585 & emsp; & emsp; 승 900 파운드 300 350 350 400 560 460 * 610 * 610 * 610 * 760 * & emsp; & emsp; & emsp; 1500 파운드 300 450 450 560 305 * 460 * 610 * 610 * 760 * 760 * & emsp; & emsp; & emsp; 2500 파운드 500 500 600 600 460 * 460 * 610 * & emsp; & emsp; & emsp; & emsp; & emsp; & emsp; 무게 (rf) 900 파운드 50 84 92 154 341 622 950 1295 1720 2380 & emsp; & emsp; & emsp; 1500 파운드 60 91 128 182 394 795 1370 2120 2800 3870 & emsp; & emsp; & emsp; 2500 파운드 121 175 195 229 720 1295 2250 & emsp; & emsp; & emsp; & emsp; & emsp; & emsp; 무게 (bw) 900 파운드 39 64 82 120 266 524 760 1090 1450 2018 년 & emsp; & emsp; & emsp; 1500 파운드 46 71 85 130 292 578 974 1615 2010 년 2815 3315 4150 5219 2500 파운드 88 135 144 158 500 892 1550 1978 2580 3780 5988 & emsp; & emsp; * 수동 기어 오퍼레이터 권장 아니. 부품 wcb 화장실 화장실 c5 cf8 cf8m 1 신체 a216 화장실 a217 화장실 a217 화장실 a217 c5 a351 cf8 a351 cf8m 2 좌석 a182 f6a a182 f22 a182 f22 a182 f5 a182 f304 a182 f316 삼 쐐기 a216 화장실 a217 화장실 a217 화장실 a217 c5 a351 cf8 a351 cf8m 4 줄기 a182 f6a saehnv3 a182 f304 a182 f316 5 스터핑 박스 a216 화장실 a217 화장실 a217 화장실 a217 c5 a351 cf8 a351 cf8m 6 씰링 아니 316l 유연한 흑연 +316 7 스플릿 링 강철 f6 f6 f6 a182 f304 f316 8 백 링 강철 강철 강철 강철 ss ss 9 볼트 a193 b7 a193 b7 a193 b7 a193 b7 a193 b8 a193 b8 10 너트 a194 2 시간 a194 2 시간 a194 2 시간 a194 2 시간 a194 gr.8 a194 gr.8 11 멍에 a216 화장실 a217 화장실 a217 화장실 a217 c5 a351 cf8 a351 cf8m 12 볼트 a193 b7 a193 b7 a193 b7 a193 b7 a193 b8 a193 b8 13 너트 a194 2 시간 a194 2 시간 a194 2 시간 a194 2 시간 a194 gr.8 a194 gr.8 14 포장 판 아니 410 아니 410 아니 410 아니 410 ANSI 304 아니 316 15 포장 유연한 흑연   그리고 반지) 또는 ptfe 16 분할 핀 강철 강철 강철 강철 강철 강철 17 아이 볼트 a193 b7 a193 b7 a193 b7 a193 b7 a193 b8 a193 b8 18 선 a182 f6 a182 f6 a182 f6 a182 f6 a182 f304 a182 f316 19 글 랜드 플랜지 a105 a105 a105 a105 a182 f304 a182 f316 20 너트 a194 2 시간 a194 2 시간 a194 2 시간 a194 2 시간 a194 gr.8 a194 gr.8 21 마개 a193 b7 a193 b7 a193 b7 a193 b7 a193 b7 a193 b7 22 줄기 너트 ni- 레지스트 a439-d2 23 기어 박스 구입 한 24 보호자 강철 25 명찰 ANSI 304 26 대갈못 ANSI 304

메시지를 남겨주세요

    에 관심이 있다면 우리의 제품과한 자세한 내용을 알고 싶다면,메시지를 남겨주십시오 여기,우리가 응답할 것입니다 당신은 빨리 우리가 할 수 있습니다.

제품

접촉