한국의

한국의

Get a Quote
제품

핫 제품

회사 뉴스

How to Install the Valve Gasket?
How to Install the Valve Gasket?
2023-06-07

Sealing gasket is a commonly used sealing spare part for machinery, equipment, etc. It is a material that plays a sealing role. Correct installation can ensure sealing performance and smooth operation of the equipment, otherwise it will damage the sealing gasket. Next, let's take a specific look at what to do. The correct installation of gaskets should be carried out when the flange connection structure or threaded connection structure, sealing surface, and gasket have been inspected without any doubt, and other valve components are intact and undamaged. 1. Before installing the gasket, apply a layer of graphite powder or lubricant mixed with engine oil (or water) to the sealing surface, gasket, thread, and rotating parts of the bolt and nut. The gasket and graphite should be kept clean. 2. The gasket should be installed on the sealing surface in a moderate and correct manner, without deviation, and should not extend into the valve chamber or rest on the shoulder. 3. Only one gasket is allowed to be installed, and it is not allowed to install two or more gaskets between the sealing surfaces to eliminate insufficient clearance between the two sealing surfaces. 4. The sealing of elliptical gaskets should ensure that the inner and outer rings of the gasket come into contact, and the two ends of the gasket should not come into contact with the bottom of the groove. 5. The installation of the O-ring should not only meet the design requirements for the ring and groove, but also have an appropriate amount of compression. On the premise of ensuring sealing, the smaller the compression deformation rate, the better, which can extend the service life of the O-ring. 6. Before installing the gasket, the valve should be in the open position to avoid affecting installation and damaging the valve components. When covering, it should be aligned with the position and should not be pushed or pulled into contact with the gasket to avoid displacement and scratches on the gasket. 7. The installation of gaskets for bolted or threaded connections should ensure that the gaskets are in a horizontal position (threaded gaskets with wrench positions should not be used with pipe wrenches). 8. Before tightening the gasket, it is necessary to have a clear understanding of the pressure, temperature, properties of the medium, and material characteristics of the gasket to determine the pre tightening force. The preload should be minimized as much as possible without leakage during pressure testing. 9. After tightening the gasket, it is necessary to ensure that there is a pre tightening gap between the connecting parts in case of gasket leakage. 10. When working at high temperatures, bolts will experience high-temperature creep, stress relaxation, and increased deformation, leading to leakage at the gasket and requiring hot tightening. On the contrary, under low temperature conditions, bolts will shrink and require cold loosening. 11. When liquid sealing gaskets are used for sealin...

게이트 밸브와 글로브 밸브의 차이점은 무엇입니까?
게이트 밸브와 글로브 밸브의 차이점은 무엇입니까?
2023-05-31

많은 사람들은 게이트 밸브와 글로브 밸브 모두 미디어를 차단하는 기능이 있으므로 사용할 때 다르지 않다고 생각합니다. 실제로 실제 적용에서 게이트 밸브와 글로브 밸브 사이에는 특정 차이점이 있습니다. 게이트 밸브 및 구조도 글로브 밸브 및 구조도 1. Having different structures. Gate valves are more complex in structure, higher in height, and larger in size than globe valves. Gate valves are shorter and higher in appearance than globe valves. Especially, opening the stem gate valve requires a higher height. If the installation position of the valve is limited, it is necessary to choose rising stem and non-rising stem gate valves and remind everyone to pay attention. 2. When fully open, it has different flow resistance. The flow resistance coefficient of ordinary gate valves is approximately 0.08~0.12. The pressure loss during the operation of the gate valve medium is small, and the fluid flow resistance is small. Gate valves are usually suitable for working conditions where frequent opening and closing are not required and the gate is kept fully open or closed. It is not suitable for adjustment and throttling. The resistance coefficient of a regular globe valve is about 3.5-4.5, and the opening and closing forces are very small. The flow resistance of the shut-off valve throughout its entire stroke is very high, and the required driving force or torque is also much greater. But it is very suitable for regulation and throttling. 3. The flow direction of the medium inside the valve body is different. Gate valves have the same effect when viewed from both sides. When installing a shut-off valve, the medium can enter from below and above the valve core. 4. The sealing surface of the gate valve has a certain degree of self-sealing ability. The valve core is in close contact with the sealing surface of the valve seat through medium pressure, achieving sealing performance and no leakage. The sealing surfaces of the shut-off valve only come into contact with each other when fully closed, and the relative sliding amount between the forcibly closed valve core and the sealing surface is very small, so the wear of the sealing surface is also very small. 5. The maintenance procedures are different. The maintenance of gate valves is not applicable to on-site pipelines, but the seat and disc of most globe valves can be replaced online without the need to remove the entire valve from the pipeline (when the valve is not under pressure). This is very suitable for situations where valves and pipelines are welded together. Gate and globe valves are both fully open and fully closed valves. When selecting valves in the application process, attention should be paid to the characteristics of the valves. Globe valves are usually used for small pipelines and better sealing performance. In steam systems and large diameter pipelines, gate valves with low fluid resistance are usually

Triple Eccentric Metal Hard Seal Butterfly Valve의 가공기술 및 구조적 특성 원문보기 KCI 원문보기 인용
Triple Eccentric Metal Hard Seal Butterfly Valve의 가공기술 및 구조적 특성 원문보기 KCI 원문보기 인용
2023-05-24

트리플 편심 메탈 하드 씰 버터 플라이 밸브는 고성능 밸브로서 내식성, 안정적인 밀봉 및 작은 개방 토크와 같은 장점이 있습니다. 밀봉 표면은 경사진 원추형 표면이며 밸브 본체 밀봉 링과 나비 플레이트 어셈블리 밀봉 링 사이의 접촉은 표면 접촉입니다. 작동 원리는 구동 장치의 토크로 나비 판 어셈블리를 직접 구동하여 나비 판 어셈블리의 밀봉 링이 밸브 본체 밀봉 링에 완전히 접촉하여 탄성 변형을 일으켜 밀봉하는 것입니다. 구조적 특성 1. The hard sealed butterfly valve adopts a three eccentric hard sealing structure, with almost no wear on the valve seat and butterfly plate, and has a sealing function that becomes tighter as the valve is closed. 2. The sealing ring is made of stainless steel, which has the dual advantages of metal hard sealing and elastic sealing. Both at low and high temperatures, it has excellent sealing performance, corrosion resistance, and long service life. 3. The sealing surface of the butterfly plate adopts surfacing cobalt based hard alloy, which is wear-resistant and has a long service life. 4. The large-sized butterfly plate adopts a quilted frame structure, with high strength, large flow area, and small flow resistance. 5. According to user requirements, hard sealed butterfly valves can be designed with bidirectional sealing function. During installation, it is not limited by the flow direction of the medium or affected by spatial location, and can be installed in any direction. 6. The drive device can be installed in multiple workstations (rotating 90 ° or 180 °), making it easy for users to use. Processing Technology Based on the structural characteristics of the triple eccentric metal hard seal butterfly valve, the sealing ring of the butterfly plate assembly is a combination of stainless steel plate, asbestos plate, or graphite. The valve body sealing ring is made of hard alloy with high hardness, and it is difficult to control the cutting amount, making it difficult to process and shape in one go. Moreover, the roughness requirements for the machined surface are very high. To ensure processing requirements, the process is as follows: Rough machining of valve body or butterfly plate assembly →→ Valve body sealing ring is welded with hard alloy for insulation and heat treatment to eliminate thermal stress →→ Sealing surface of rough turning of upper tooling →→ Upper tooling precision turning sealing surface →→ Grinding sealing surface with upper grinding head →→ Boring shaft holes for valve body and butterfly plate assembly →→ Strength test sealing test

1 인치 800lb 게이트 밸브 BB OSY SW
加载中...

1 인치 800lb 게이트 밸브 BB OSY SW

1 인치 800lb 게이트 밸브는 sw 및 핸드 휠 작동이 포함 된 API 602에 따라 설계되었습니다. 스테인리스 스틸 f316 게이트 밸브는 볼트로 고정 된 보닛, 외부 나사 및 요크 구조로되어 있습니다.

  • 지불:

    30% when order confirmed, 70% before shipment
  • 제품 원산지:

    China
  • 색:

    Customization
  • 배송 포트:

    Shanghai, China
  • 리드 타임:

    30~60 days Ex Works after order confirmation
  • Material:

    F316
  • Method of Operation:

    Handwheel
지금 문의
제품 상세 정보

빠른 세부 사항

유형

게이트 밸브

크기

1 인치

설계 압력

800 파운드

구성

b.b; OS & y;

연결 타입

SW

작업 유형

핸드 휠

바디 재질

f316

디스크 소재

f316

디자인 코드

API 602

플랜지 끝

asme b16.11

검사 및 테스트

API 598

매질

물, 기름, 가스

유래

중국


기술 도면


포장



dervos에 대해

10 년 넘게 밸브 산업을 전문으로하는 dervos는 게이트, 글로브, 체크, 볼, 버터 플라이, 플러그 밸브 및 스트레이너의 선두 공급 업체가되었습니다. 우리는 지역 파트너와 함께 lukoil, mol, ypf와 같은 석유 및 가스 사용자에게 서비스를 제공합니다.

dervos는 다음과 같은 장점을 보여줍니다.

1. 수십 개의 안정적인 공급 업체와의 파트너십을 통해 경쟁력있는 가격으로 다양한 고품질 제품을 고객에게 제공 할 수 있습니다.

2. 각 순서는 납품의 앞에 검사보고를 가진 엄격한 품질 관리하에 있습니다.

3. 우리는 고객만큼 배달 시간을 소중하게 생각합니다. 강력한 구매 시스템을 통해 우리는 정시 배송을 보장하기 위해 각 주문을 면밀히 따릅니다.

4.원 스톱 솔루션이 적시에 제공됩니다.




메시지를 남길

에 관심이 있다면 우리의 제품과한 자세한 내용을 알고 싶다면,메시지를 남겨주십시오 여기,우리가 응답할 것입니다 당신은 빨리 우리가 할 수 있습니다.

관련 상품
볼트 형 보닛 단조 게이트 밸브
단조 스틸 a105 게이트 밸브 스레드 1 인치 2500 파운드

솔리드 웨지, 포트 감소, 볼트 보닛, 핸드 휠, 상승 스템 및 암나사 (fnpt)의 1 인치 2500lb 고압 단조 강철 게이트 밸브 기능. 단조 밸브는 API 602 및 API 598을 준수합니다. 빠른 세부 사항 유형 문   판막 크기 1'' 압력 수업   2500 구성 bb,   상승 줄기, OS 및 Y, 솔리드 웨지 연결 실   연결 조작 핸드 휠   움직이는 바디 재료 ASTM   a105 트림 재료 13cr + stl 디자인 API 602 끝으로 종료 ASTM B16.10 압력 및 온도 ASTM B16.34 연결 끝 ASTM B1.20.1 온도 범위 -29 ℃ ~ + 425 ℃ 매질 울다 유래 중국 제품 범위바디 재질 : 탄소강, 스테인레스 스틸, 합금강, 저온 스틸보통 지름 : 1 / 2’~ 4’연결구 : bw, sw, 플랜지, 나사산압력 범위 : 150lbs ~ 2500lbs (pn16 ~ pn420)작동 : 핸드 휠, 베어 스템, 액추에이터 포함작동 온도 : -46 ℃ ~ + 425 ℃ 제조 과정에서 품질을 어떻게 관리합니까? 주조 검사 : 외관, 벽 두께, 수량, 크기 및 원본 재료 보고서 등을 확인하십시오. 자격이없는 경우 가공하기 전에 ms sp sp 55를 충족시켜야합니다. 가공 감독 :공장을 무작위로 방문하여 제조 공정을 점검하여 생산 공정을 감독하고 잘못된 생산 또는 잘못된 생산 설계를 피할 수있는 잠재적 인 문제를 찾습니다.

API602 게이트 밸브
api602 게이트 밸브 1 인치 0.75 인치 900lb bw 핸드 휠

api602 게이트 밸브 볼트 보닛 외부 스크류 요크 솔리드 웨지 감소 보어 맞대기 용접 연결 sch80s a182 f11 바디 트림 # 5 (13 % cr + stl) 900lb 1 인치 3/4 인치 빠른 세부 사항 유형 게이트 밸브 크기 3/4 인치 -1 인치 설계 압력 cl900 구성 bb, os & amp; y 연결 타입 bw 작업 유형 핸드 휠 바디 재료 f11 쐐기 f6a + stl 줄기 재료 f6a 시트 재료 f6a + stl 디자인 코드 API 602 대면 치수 asme b16.10 테스트 및 검사 API 598 압력 및 온도 asme b16.34 매질 물, 기름 및 가스 유래 중국 api602 게이트 밸브 1 인치 0.75 인치 900lb bw 핸드 휠

A105N 0.5 인치 rf 게이트 밸브
일체형 플랜지 볼트 보닛 A105N 풀 보어 게이트 밸브

api602 게이트 밸브 볼트 보닛 외부 스크류 요크 솔리드 웨지 풀 보어 일체형 돌출면 플랜지 연결 a105n 바디 트림 13cr 150lb 300lb 1/2 인치 3/4 인치 a182 f6a 시트 / 웨지 / 줄기, 304+ 흑연 / 가스켓 & nbsp;

800lb dn20 게이트 밸브
dn20 800lb 단조 스틸 a105 sw bb 핸드 휠 게이트 밸브 a105

dn20 800lb pn130 단조 스틸 a105 sw 연결 방식 bb os 및 y 핸드 휠 작동 게이트 밸브 바디 및 보닛 a105 api600 트림 8 시트 410 + stl 웨지 420 스템 410 가스켓 304+ 흑연 디자인 및 제조 api602 대면 ansi b16.11 용접 엔드 치수 API 602 테스트 및 검사 API 508. 빠른 세부 사항 유형 게이트 밸브 크기 dn20 압력 800 파운드 구성 bb, OS & amp; y 연결 sw 작동 모드 핸드 휠 바디 재료 a105 덮개 a105 디자인 및 제조 API 602 연결 종료 API 602 검사 API 598 온도 범위 -29 ℃ ~ + 425 ℃ 매질 기름, 물, 가스

다섯 개의 백성 중 하나
구멍 단조 게이트 밸브, 용접 된 보닛, 일체형 플랜지

중국 용접 보닛 게이트 밸브 생산자가 제작 된 보어 단조 스틸 게이트 밸브, A105N, 1 / 2-4 인치, 150-1500 LB, 용접 보닛, 일체형 플랜지.

단조 게이트 밸브
1 인치 600LB 단조 게이트 밸브 API 600 핸드휠 상승 스템

중국 1인치 게이트, 밸브 제조업체 Dervos는 1인치 게이트 밸브를 제공합니다. A105 , API 600, 클래스600, 플랜지, 핸드휠 작업.

게이트 밸브
단조 강철 게이트 밸브 1 인치 300LB 솔리드 웨지

1인치 단조 강철 게이트 밸브는 일체형 플랜지, 볼트식 보닛, 상승 스템 및 솔리드 쐐기 및 볼트식 보닛.으로 구성됩니다. 밸브에는 설계 표준 API 602 및 검사 표준 API 598.이 있습니다. dervos는 고객에게 다양한 크기, 재질, 표준, 설계 압력, 구조, 작동 유형 및 연결 유형.의 밸브를 제공함으로써 맞춤형 서비스를 제공할 수 있습니다.

게이트 밸브
1" 800LB 단조 강철 게이트 밸브 BW*NPT F5 API602

1" 800LB 게이트 밸브는 API 602 표준에 따라 제작됩니다. 밸브 본체는 A182-F5로 제작됩니다. 견고한 게이트, 용접된 보닛 및 확장된 밸브 본체 100mm의 구조적 특성을 가지고 있습니다. 연결 모드는 BW*NPT입니다. 그리고 그것은 핸드 휠 작동 모드가 있습니다.

게이트 밸브
DN50 PN40는 강철 게이트 밸브 A105 손 바퀴 ISO를 위조했습니다

DN50 PN40 게이트 밸브는 EN ISO 15761 표준에 따라 만들어집니다. 밸브 본체는 ASTM A105N으로 제작되었습니다. 그것은 단단한 쐐기, 풀 보어, 상승 줄기 및 볼트 커버의 구조적 특성을 가지고 있습니다. 연결 모드는 EN1092-1 B1입니다. 그리고 핸드 휠 작동 모드가 있습니다.

게이트 밸브
1/2" 300LB 단조 강철 게이트 밸브 A105N API602 BB OS&Y RF

1/2" 300LB 게이트 밸브는 API602 및 ASME B16.34 표준에 따라 제작됩니다. 밸브 본체는 A105N으로 제작됩니다. BB, OS&Y, 견고한 웨지, NACE MR0175, 부식 허용 3mm 및 누설 수준 ISO5208A의 구조적 특성을 가집니다. .연결모드는 전반적으로 RF이며 핸드휠 동작모드가 있습니다.

트러 니언 장착 볼 밸브
트러 니언 장착 DN300 PN63 DBB 볼 밸브

트러 니언 장착 볼 밸브 dn300 pn63 풀 보어 더블 블록 및 블리드 pmss 씰 (메탈 씰 + 소프트 씰) lf2 바디, lf2 + enp 볼 / 시트 및 410 스템으로 블로우 아웃 방지 스템 기어 박스 작동. 빠른 세부 사항 유형 볼 밸브 크기 dn300 설계 압력 pn63 구성 dbb, 트러 니언 장착 볼 밸브 연결 타입 플랜지 작업 유형 기어 박스 작동 바디 재료 lf2 볼 재료 lf2 + enp 줄기 재료 410 시트 재료 lf2 + enp 디자인 코드 API 6D 대면 치수 API 6D 연결 종료 asme b16.5 압력 및 온도 asme b16.34 매질 물, 기름 및 가스 유래 중국

게이트 밸브
1" 800LB 단조 강철 게이트 밸브 BW*NPT F5 API602

1" 800LB 게이트 밸브는 API 602 표준에 따라 제작됩니다. 밸브 본체는 A182-F5로 제작됩니다. 견고한 게이트, 용접된 보닛 및 확장된 밸브 본체 100mm의 구조적 특성을 가지고 있습니다. 연결 모드는 BW*NPT입니다. 그리고 그것은 핸드 휠 작동 모드가 있습니다.

메시지를 남겨주세요

    에 관심이 있다면 우리의 제품과한 자세한 내용을 알고 싶다면,메시지를 남겨주십시오 여기,우리가 응답할 것입니다 당신은 빨리 우리가 할 수 있습니다.

제품

접촉